LK Automation Limited
MR-J3-11KB-RJ080W For direct drive servo motor drive MITSUBISHI MR-J3-11KB-RJ080W
Brand:
MITSUBISHI
Name: For direct drive servo motor drive
Model: MR-J3-11KB-RJ080W
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 11.0kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for direct drive servo motor.
Power specification: three phase AC200V.
Direct drive system suitable for high speed and high precision!
High speed operation can be realized by direct drive (2m/s), and the traditional mechanical transmission can not achieve such a high speed.
The full closed loop control can be realized by using the position feedback signal from the load side encoder, such as the linear encoder.
The use of a flexible linear servo motor drive components can make the system more compact structure.
The primary side of the linear servo motor (motor coil) is sliding along the secondary side (permanent magnet) of the motor,
So linear servo motor is especially suitable for large range of applications. In addition, linear servo motor can be connected in series,
Especially for large systems in two axes for high precision synchronous operation.
...More relevant models >>>>
Name: For direct drive servo motor drive
Model: MR-J3-11KB-RJ080W
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 11.0kw.
Interface type: SSCNET type III fiber communication.
Special specification: suitable for direct drive servo motor.
Power specification: three phase AC200V.
Direct drive system suitable for high speed and high precision!
High speed operation can be realized by direct drive (2m/s), and the traditional mechanical transmission can not achieve such a high speed.
The full closed loop control can be realized by using the position feedback signal from the load side encoder, such as the linear encoder.
The use of a flexible linear servo motor drive components can make the system more compact structure.
The primary side of the linear servo motor (motor coil) is sliding along the secondary side (permanent magnet) of the motor,
So linear servo motor is especially suitable for large range of applications. In addition, linear servo motor can be connected in series,
Especially for large systems in two axes for high precision synchronous operation.
Motor series: low inertia, low power.
Rated output power: 0.2kw.
Rated speed: 3000r/min.
Whether with brake: No.
Shaft end: Standard (straight).
Protection level: IP55 does not include the shaft part and the connector.
Features: low inertia is particularly suitable for high speed motor (6000 or 12000 RPM / min) of general industrial machinery MITSUBISHI MR-J3-11KB-RJ080W.
Application example 1: drive belt drive, robot MR-J3-11KB-RJ080W
Application example 2: assembly machine, sewing machine, X-Y working table.
Application example 3: food manufacturing machinery, semiconductor manufacturing equipment, knitting machine and embroidery machine.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed MITSUBISHI MR-J3-11KB-RJ080W.
All motor dimensions are the same as before and all are compatible with the wiring. Motor series: low inertia, small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.3kw.
Rated speed: 3000rpm.
With the brake: without.
Shaft end: straight shaft.
AC servo motor and brushless DC servo motor in the function of the difference: AC servo is better, because it is a sine wave control, torque ripple small MITSUBISHI MR-J3-11KB-RJ080W.
DC servo is a trapezoidal wave. DC servo is simple and cheap. A power supply connector set for HC-KFS; HC-MFS; 3000r/min HC-UFS servo motor.
For MR-J2S-11KA (4) MR-J2S-22KA to (4) MR-J3-11KB-RJ080W MITSUBISHI. Drive: MR-H_ACN series built-in positioning function.
Rated output: 3.5KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop MR-J3-11KB-RJ080W MITSUBISHI.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement MR-J3-11KB-RJ080W MITSUBISHI.
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting tthe minimum detectable speed MR-J3-11KB-RJ080W.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is largger MITSUBISHI MR-J3-11KB-RJ080W.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method.
Rated output power: 0.2kw.
Rated speed: 3000r/min.
Whether with brake: No.
Shaft end: Standard (straight).
Protection level: IP55 does not include the shaft part and the connector.
Features: low inertia is particularly suitable for high speed motor (6000 or 12000 RPM / min) of general industrial machinery MITSUBISHI MR-J3-11KB-RJ080W.
Application example 1: drive belt drive, robot MR-J3-11KB-RJ080W
Application example 2: assembly machine, sewing machine, X-Y working table.
Application example 3: food manufacturing machinery, semiconductor manufacturing equipment, knitting machine and embroidery machine.
High resolution encoder 131072p/rev (17 bit).
The encoder with high resolution ensures excellent performance and stability at low speed MITSUBISHI MR-J3-11KB-RJ080W.
All motor dimensions are the same as before and all are compatible with the wiring. Motor series: low inertia, small capacity.
Using a serial absolute / incremental encoder.
Rated output power: 0.3kw.
Rated speed: 3000rpm.
With the brake: without.
Shaft end: straight shaft.
AC servo motor and brushless DC servo motor in the function of the difference: AC servo is better, because it is a sine wave control, torque ripple small MITSUBISHI MR-J3-11KB-RJ080W.
DC servo is a trapezoidal wave. DC servo is simple and cheap. A power supply connector set for HC-KFS; HC-MFS; 3000r/min HC-UFS servo motor.
For MR-J2S-11KA (4) MR-J2S-22KA to (4) MR-J3-11KB-RJ080W MITSUBISHI. Drive: MR-H_ACN series built-in positioning function.
Rated output: 3.5KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop MR-J3-11KB-RJ080W MITSUBISHI.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement MR-J3-11KB-RJ080W MITSUBISHI.
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting tthe minimum detectable speed MR-J3-11KB-RJ080W.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is largger MITSUBISHI MR-J3-11KB-RJ080W.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method.
...More relevant models >>>>