LK Automation Limited
High speed counter module RD62P2 MITSUBISHI RD62P2
Brand:
MITSUBISHI
Name: High speed counter module
Model: RD62P2
DC input, transistor (drain type) output.
Channel number: 2CH.
External wiring connection mode: 40 pin connector
Count input signal: there
Single phase input (single frequency / double frequency)
Dual phase input (single frequency and double frequency /4)
CW/CCW input: there
The signal level (phi A, Phi B): 2 ~ 5mA DC5/12/24V.
High speed counter module can be measured in 200kpulse/s when DC input,
8Mpulse/s measurement can be performed in a differential input.
The use of high precision incremental encoder, the most suitable for location tracking.
In addition, the high-speed counter module is also equipped with a pulse measurement and PWM output and other functions.
...More relevant models >>>>
Name: High speed counter module
Model: RD62P2
DC input, transistor (drain type) output.
Channel number: 2CH.
External wiring connection mode: 40 pin connector
Count input signal: there
Single phase input (single frequency / double frequency)
Dual phase input (single frequency and double frequency /4)
CW/CCW input: there
The signal level (phi A, Phi B): 2 ~ 5mA DC5/12/24V.
High speed counter module can be measured in 200kpulse/s when DC input,
8Mpulse/s measurement can be performed in a differential input.
The use of high precision incremental encoder, the most suitable for location tracking.
In addition, the high-speed counter module is also equipped with a pulse measurement and PWM output and other functions.
Analog output channel number: 16CH.
accuracy
Ambient temperature of 25 plus or minus 5 degrees C: plus or minus 0.1%.
Ambient temperature 0 ~ 55 degrees C:-.
Temperature coefficient: positive and negative 50ppm/.
Conversion speed: 1ms/CH.
Insulation between channels: isolation transformer insulation MITSUBISHI RD62P2.
Output short circuit protection: have.
External power supply: -.
External wiring connection: 40 pin connector two RD62P2
Voltage output
Digital input value: 32000 ~ 32000.
Analog output voltage: DC - 10 - 10V.
Current output
Digital input value: 0 ~ 32000.
Analog output current: DC0 ~ 20mA.
Without using a special program to create the waveform, can reduce the programming time.
Easy to use parameters to set the conversion operation and scaling, no need to create a dedicated program MITSUBISHI RD62P2.
Therefore, it is helpful to reduce the development cost of the program and to reduce the program capacity.
High speed output flow simulation waveform.
The analog output module has the function of registering arbitrary waveform data to the module, and continuously executing the analog output according to the set conversion cycle MITSUBISHI RD62P2.
Execute the analog quantity (torque) control of stamping machine and injection molding machine, can automatically output the control waveform,
Through the process of high speed, smooth control. In addition, only prior to the waveform data are registered in the module,
Can easily control the analog waveform, so the production line control, such as repetitive control,Input points: 16 points RD62P2 MITSUBISHI RD62P2 MITSUBISHI.
Rated input voltage and frequency: DC24V.
Rated input current: 6.0mA.
Response time: 5 S ~ 70ms.
Common way: 8 point / public end (negative public end).
Interrupt function: have.
External wiring connection mode: 18 point screw terminal.
The input module is the most used module in the control system RD62P2 MITSUBISHI.
According to the input voltage, the input points of different, choose the most suitable user needs of the module.
1 modules are equipped with a variety of functions.
Can be through a single input module to 1 points for the unit to set the high speed response, interrupt input function.
In addition, the publlic end of the module can be freely selected as the common end of the positive pole and the negative pole RD62P2.
It is not necessary to use different modules according to the input specifications and functions, and reduce the number of mmodules,
Therefore slot occupied quantity can be reduced by 20% than in the past, the deployment cost can be reduced by 60% compared with the previous MITSUBISHI RD62P2.
accuracy
Ambient temperature of 25 plus or minus 5 degrees C: plus or minus 0.1%.
Ambient temperature 0 ~ 55 degrees C:-.
Temperature coefficient: positive and negative 50ppm/.
Conversion speed: 1ms/CH.
Insulation between channels: isolation transformer insulation MITSUBISHI RD62P2.
Output short circuit protection: have.
External power supply: -.
External wiring connection: 40 pin connector two RD62P2
Voltage output
Digital input value: 32000 ~ 32000.
Analog output voltage: DC - 10 - 10V.
Current output
Digital input value: 0 ~ 32000.
Analog output current: DC0 ~ 20mA.
Without using a special program to create the waveform, can reduce the programming time.
Easy to use parameters to set the conversion operation and scaling, no need to create a dedicated program MITSUBISHI RD62P2.
Therefore, it is helpful to reduce the development cost of the program and to reduce the program capacity.
High speed output flow simulation waveform.
The analog output module has the function of registering arbitrary waveform data to the module, and continuously executing the analog output according to the set conversion cycle MITSUBISHI RD62P2.
Execute the analog quantity (torque) control of stamping machine and injection molding machine, can automatically output the control waveform,
Through the process of high speed, smooth control. In addition, only prior to the waveform data are registered in the module,
Can easily control the analog waveform, so the production line control, such as repetitive control,Input points: 16 points RD62P2 MITSUBISHI RD62P2 MITSUBISHI.
Rated input voltage and frequency: DC24V.
Rated input current: 6.0mA.
Response time: 5 S ~ 70ms.
Common way: 8 point / public end (negative public end).
Interrupt function: have.
External wiring connection mode: 18 point screw terminal.
The input module is the most used module in the control system RD62P2 MITSUBISHI.
According to the input voltage, the input points of different, choose the most suitable user needs of the module.
1 modules are equipped with a variety of functions.
Can be through a single input module to 1 points for the unit to set the high speed response, interrupt input function.
In addition, the publlic end of the module can be freely selected as the common end of the positive pole and the negative pole RD62P2.
It is not necessary to use different modules according to the input specifications and functions, and reduce the number of mmodules,
Therefore slot occupied quantity can be reduced by 20% than in the past, the deployment cost can be reduced by 60% compared with the previous MITSUBISHI RD62P2.
...More relevant models >>>>