LK Automation Limited
servo motor SGMSV-15D3A6E Yaskawa SGMSV-15D3A6E
Brand:
Yaskawa
Name: servo motor
Model: SGMSV-15D3A6E
Sigma -V series servo motor SGMSV.
Rated output: 1.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: servo motor
Model: SGMSV-15D3A6E
Sigma -V series servo motor SGMSV.
Rated output: 1.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specification: dynamic brake (DB).
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Function: no deviation standard Yaskawa SGMSV-15D3A6E.
High performance sigma shaped -V-EX series SGMSV-15D3A6E
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control Yaskawa SGMSV-15D3A6E. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load Yaskawa SGMSV-15D3A6E.
Full closed loop module.
Maximum applicable motor capacity: 3.0kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK- II communication command type (rotary servo motor) SGMSV-15D3A6E Yaskawa.
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMSV-15D3A6E Yaskawa.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response SGMSV-15D3A6E Yaskawa.
External encoder capable of corresponding high resolution (linear grating). Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGMSV-15D3A6E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specification: dynamic brake (DB).
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Function: no deviation standard Yaskawa SGMSV-15D3A6E.
High performance sigma shaped -V-EX series SGMSV-15D3A6E
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control Yaskawa SGMSV-15D3A6E. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load Yaskawa SGMSV-15D3A6E.
Full closed loop module.
Maximum applicable motor capacity: 3.0kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK- II communication command type (rotary servo motor) SGMSV-15D3A6E Yaskawa.
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMSV-15D3A6E Yaskawa.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response SGMSV-15D3A6E Yaskawa.
External encoder capable of corresponding high resolution (linear grating). Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGMSV-15D3A6E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
...More relevant models >>>>