LK Automation Limited LK Automation Limited
Brand: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Go Back >> Product Catalogues
SGMPS-08A2E2CE Medium inertia flat type motor Yaskawa SGMPS-08A2E2CE
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-08A2E2CE
Sigma -V series servo motor SGMPS.
Rated output: 750W (0.75kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control Yaskawa SGMPS-08A2E2CE SGMPS-08A2E2CE
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command Yaskawa SGMPS-08A2E2CE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly Yaskawa SGMPS-08A2E2CE. Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 3.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: straight shaft without key SGMPS-08A2E2CE Yaskawa.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMPS-08A2E2CE Yaskawa.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type SGMPS-08A2E2CE Yaskawa.
Rated speed: 1500r\/min.
Power: 1.3kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,

Alarm can only turn off the main circuit power supply, easy to maintain SGMPS-08A2E2CE.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 Yaskawa SGMPS-08A2E2CE.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control


...More relevant models >>>>