LK Automation Limited
SGMPS-01ACE6EE Yaskawa SGMPS-01ACE6EE
Brand:
Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-01ACE6EE
Sigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Medium inertia flat type motor
Model: SGMPS-01ACE6EE
Sigma -V series servo motor SGMPS.
Rated output: 100W (0.1kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor type SGMAH (speed: 3000r/min).
Power: 30W.
Power supply voltage: single phase AC100V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: no brake oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1/3, to achieve a good response Yaskawa SGMPS-01ACE6EE SGMPS-01ACE6EE
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the Yaskawa SGMPS-01ACE6EE.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop / control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance.DC power input servo unit type SGDV.
Maximum applicable motor capacity: 11W.
Power supply voltage: DC48V Yaskawa SGMPS-01ACE6EE.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: B.
Realize real time communication.
The maximum transmission speed is 10Mbps, the communication cycle of 250 tested s ~ 4ms (depending on the device),
Can carry up to 30 stations of the high speed control. Through the high speed of communication, can send and receive all kinds of control information in real time.
Energy saving and high efficiency
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPS-01ACE6EE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizatioon phase control SGMPS-01ACE6EE.
Because the control mode can be switched on line, the complicated mechanical efficiency can be realized more effectively and smoothly.
Power: 30W.
Power supply voltage: single phase AC100V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: no brake oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1/3, to achieve a good response Yaskawa SGMPS-01ACE6EE SGMPS-01ACE6EE
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the Yaskawa SGMPS-01ACE6EE.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop / control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance.DC power input servo unit type SGDV.
Maximum applicable motor capacity: 11W.
Power supply voltage: DC48V Yaskawa SGMPS-01ACE6EE.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: B.
Realize real time communication.
The maximum transmission speed is 10Mbps, the communication cycle of 250 tested s ~ 4ms (depending on the device),
Can carry up to 30 stations of the high speed control. Through the high speed of communication, can send and receive all kinds of control information in real time.
Energy saving and high efficiency
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPS-01ACE6EE.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizatioon phase control SGMPS-01ACE6EE.
Because the control mode can be switched on line, the complicated mechanical efficiency can be realized more effectively and smoothly.
...More relevant models >>>>