LK Automation Limited LK Automation Limited
Brand: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Go Back >> Product Catalogues
SGMPH-04AAA6C Servo motor Yaskawa SGMPH-04AAA6C
Brand: Yaskawa
Name: Servo motor
Model: SGMPH-04AAA6C
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with DC24V brake.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated.

Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load Yaskawa SGMPH-04AAA6C.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMPH-04AAA6C
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMPS Yaskawa SGMPH-04AAA6C.
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive Yaskawa SGMPH-04AAA6C.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55 SGMPH-04AAA6C Yaskawa. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C SGMPH-04AAA6C Yaskawa.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGMPH-04AAA6C Yaskawa.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMPH-04AAA6C.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control Yaskawa SGMPH-04AAA6C.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.


...More relevant models >>>>
Related download