LK Automation Limited
SGMCS-14M3A11 | Yaskawa Direct drive servo motor SGMCS-14M3A11
Brand:
Yaskawa
Name: Direct drive servo motor
Model: SGMCS-14M3A11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 14N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Name: Direct drive servo motor
Model: SGMCS-14M3A11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 14N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -7 series servo unit SGD7S.
Maximum applicable motor capacity: 0.1kW.
Voltage: single phase \/ three phase AC200V.
Interface: analog voltage, pulse sequence.
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Select servo.
Since the Yaskawa since the beginning of 1992 sales of sigma series, has always attached great importance to technical exchanges and customer,
In order to solve the new problem of customer machinery, and repeatedly to carry out technical innovation Yaskawa SGMCS-14M3A11 SGMCS-14M3A11
High speed, high accuracy, the use of convenience in recent years has been the requirement of customers,
But the degree of its requirement is continuously deepening.
2014, the servo drive upgrade to have 7 major advantages",
Provide solutions for customers unique yaskawa Yaskawa SGMCS-14M3A11.
With its excellent performance, convenient operation, long life cycle, etc.,
In all these areas will have great potential, provides solutions to the shocking. "Choose servo, choose"Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B Yaskawa SGMCS-14M3A11.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-14M3A11 Yaskawa.
Parameter setting device.
The parameters can be directly entered by the servo drive body SGMCS-14M3A11 Yaskawa.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V SGMCS-14M3A11 Yaskawa.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-14M3A11.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control Yaskawa SGMCS-14M3A11.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 0.1kW.
Voltage: single phase \/ three phase AC200V.
Interface: analog voltage, pulse sequence.
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Select servo.
Since the Yaskawa since the beginning of 1992 sales of sigma series, has always attached great importance to technical exchanges and customer,
In order to solve the new problem of customer machinery, and repeatedly to carry out technical innovation Yaskawa SGMCS-14M3A11 SGMCS-14M3A11
High speed, high accuracy, the use of convenience in recent years has been the requirement of customers,
But the degree of its requirement is continuously deepening.
2014, the servo drive upgrade to have 7 major advantages",
Provide solutions for customers unique yaskawa Yaskawa SGMCS-14M3A11.
With its excellent performance, convenient operation, long life cycle, etc.,
In all these areas will have great potential, provides solutions to the shocking. "Choose servo, choose"Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B Yaskawa SGMCS-14M3A11.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-14M3A11 Yaskawa.
Parameter setting device.
The parameters can be directly entered by the servo drive body SGMCS-14M3A11 Yaskawa.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V SGMCS-14M3A11 Yaskawa.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pullse generator for D/A converter or position instruction without speed / torque command SGMCS-14M3A11.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control Yaskawa SGMCS-14M3A11.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>