LK Automation Limited
SGM7A-30AFA6C | Yaskawa SGM7A-30AFA6C Low inertia, high speed servo motor
Brand:
Yaskawa
Name: Low inertia, high speed servo motor
Model: SGM7A-30AFA6C
Low inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse).
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problem
...More relevant models >>>>
Name: Low inertia, high speed servo motor
Model: SGM7A-30AFA6C
Low inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse).
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problem
Sigma -V series servo motor SGMSV.
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) Yaskawa SGM7A-30AFA6C.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGM7A-30AFA6C0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type Yaskawa SGM7A-30AFA6C.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationHigh performance, use the best type of servo unit (high performance) Yaskawa SGM7A-30AFA6C.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specifications: shelf installation type + paint SGM7A-30AFA6C Yaskawa.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Function: no deviation standard.
High performance sigma shaped -V-EX series SGM7A-30AFA6C Yaskawa.
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved SGM7A-30AFA6C Yaskawa.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control. Full closed loop module.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop moddule SGM7A-30AFA6C.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response Yaskawa SGM7A-30AFA6C.
External encoder capable of corresponding high resolution (linear grating).
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) Yaskawa SGM7A-30AFA6C.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGM7A-30AFA6C0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type Yaskawa SGM7A-30AFA6C.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationHigh performance, use the best type of servo unit (high performance) Yaskawa SGM7A-30AFA6C.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A.
Hardware specifications: shelf installation type + paint SGM7A-30AFA6C Yaskawa.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Function: no deviation standard.
High performance sigma shaped -V-EX series SGM7A-30AFA6C Yaskawa.
2 models of high performance servo unit.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved SGM7A-30AFA6C Yaskawa.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control. Full closed loop module.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop moddule SGM7A-30AFA6C.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response Yaskawa SGM7A-30AFA6C.
External encoder capable of corresponding high resolution (linear grating).
...More relevant models >>>>