LK Automation Limited
Simple motion control positioning module FX5-40SSC-S MITSUBISHI FX5-40SSC-S
Brand:
MITSUBISHI
Name: Simple motion control positioning module
Model: FX5-40SSC-S
Function: simple motion control 4 axis positioning (corresponding to SSCNET III /H).
Input and output points: 8 points.
Positioning control via /H III SSCNET.
FX5-40SSC-S is equipped with the corresponding SSCNET III /H 4 axis positioning function module.
Table operation, combined with linear interpolation, circular interpolation between the 2 axes, and the connection trajectory control,
Smooth positioning control can be easily realized.
Positioning function of 8CH high speed pulse input and 4 axis pulse output by FX5U/FX5UC.
In addition, the high speed output can be set through the table, which can be realized through special instructions, which can be used to realize the function of interrupt location, variable speed operation and simple interpolation.
...More relevant models >>>>
Name: Simple motion control positioning module
Model: FX5-40SSC-S
Function: simple motion control 4 axis positioning (corresponding to SSCNET III /H).
Input and output points: 8 points.
Positioning control via /H III SSCNET.
FX5-40SSC-S is equipped with the corresponding SSCNET III /H 4 axis positioning function module.
Table operation, combined with linear interpolation, circular interpolation between the 2 axes, and the connection trajectory control,
Smooth positioning control can be easily realized.
Positioning function of 8CH high speed pulse input and 4 axis pulse output by FX5U/FX5UC.
In addition, the high speed output can be set through the table, which can be realized through special instructions, which can be used to realize the function of interrupt location, variable speed operation and simple interpolation.
Protocol: SLMP, TCP/IP, UDP, SNTP.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Can be low cost will be connected to the FX3 series Ethernet.
Support data monitoring, can monitor the basic unit through the computer browser,
Remote maintenance can be carried out by Works2 GX in a place far from the scene MITSUBISHI FX5-40SSC-S.
Connect FX3SA, FX3S, FX3GA, FX3G, FX3U host, you need to convert the adapter or function expansion board FX5-40SSC-S Max input / output points: 10 points.
Supply voltage: 100 - 240VAC.
Input points: 6 points.
Output points: 4 points.
Output type: relay.
Power consumption (W): 19.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX5-40SSC-S.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor MITSUBISHI FX5-40SSC-S.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication FX5-40SSC-S MITSUBISHI. Max input / output points: 30 points.
Supply voltage: 100 - 240VAC.
Input points: 16 points.
Output points: 14 points.
Output type: Transistor (source) FX5-40SSC-S MITSUBISHI.
Power consumption (W): 21.
Weight (kg):0.45.
Size (WxHxD) mm:100x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator FX5-400SSC-S MITSUBISHI FX5-40SSC-S.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and caan be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FX5-40SSC-S.
Communication mode: full duplex / half duplex.
At the same time can open a few: 4 connection.
Weight: 0.3kg.
Can be low cost will be connected to the FX3 series Ethernet.
Support data monitoring, can monitor the basic unit through the computer browser,
Remote maintenance can be carried out by Works2 GX in a place far from the scene MITSUBISHI FX5-40SSC-S.
Connect FX3SA, FX3S, FX3GA, FX3G, FX3U host, you need to convert the adapter or function expansion board FX5-40SSC-S Max input / output points: 10 points.
Supply voltage: 100 - 240VAC.
Input points: 6 points.
Output points: 4 points.
Output type: relay.
Power consumption (W): 19.
Weight (kg):0.22.
Size (WxHxD) mm:60x90x49.
Host has 10 points (6I/4O), 14 points (8I/6O), 20 points (12I/8O), 30 points (16I/14O) of 4 types MITSUBISHI FX5-40SSC-S.
This type of PLC is mainly used in all of the digital input, digital output control point of the device.
Can be directly connected to the 220V city power, built-in 8K step EEPROM memory, no battery, easy to maintain.
The series transistor output (MT) of the PLC, can be output 2 100KHz pulse, direct drive servo or stepper motor MITSUBISHI FX5-40SSC-S.
The series PLC can not be brought with the expansion module, but can be installed by the BD board to extend a small amount of I/O.
The series 1N through the installation of BD series PLC board, can achieve RS232, RS485, RS422 communication FX5-40SSC-S MITSUBISHI. Max input / output points: 30 points.
Supply voltage: 100 - 240VAC.
Input points: 16 points.
Output points: 14 points.
Output type: Transistor (source) FX5-40SSC-S MITSUBISHI.
Power consumption (W): 21.
Weight (kg):0.45.
Size (WxHxD) mm:100x90x75.
All equipment is digital input and output point.
The total I/O points are not more than 30 points, and the input points are less than 16, the output points are less than 14.
Its MT series of PLC can drive 2 way servo or stepper, commonly used in the control system for a simple manipulator FX5-400SSC-S MITSUBISHI FX5-40SSC-S.
MITSUBISHI FX1S series PLC is suitable for the smallest package,
It is the preferred target for low cost users to seek powerful control over a limited range of I/0.
FX1S provides up to 30 I/O points, and caan be transmitted through serial communication data,
MT models also have the ability to locate, widely used in a variety of small mechanical equipment MITSUBISHI FX5-40SSC-S.
...More relevant models >>>>