LK Automation Limited
MR-J3-15KT4 | MITSUBISHI MR-J3-15KT4 CC-Link communication driver
Brand:
MITSUBISHI
Name: CC-Link communication driver
Model: MR-J3-15KT4
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 15.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register.
...More relevant models >>>>
Name: CC-Link communication driver
Model: MR-J3-15KT4
MITSUBISHI motor universal AC servo amplifier MELSERVO-J3 series.
Rated output: 15.0kw.
Interface type: CC-Link communication type (built-in positioning function).
Power specification: three phase AC400V.
Positioning operation by setting position and rotational speed data in the positioning table and receiving the start signal from the main controller.
The setting of the position and speed of the positioning table, as well as the start and stop operation can be completed through CC-Link communication.
By using the MR-J3-D01 extension IO unit, the DI/O instruction can be used to select and locate the table.
(CC-Link can not be used for MR-J3-D01 communications).
With built-in positioning function of the servo amplifier, can be set through the CC-Link communications and speed data. (corresponding to the CC-Link version: Ver.1.10)
Can be achieved through the CC-Link communications to start, stop and monitoring and other operations.
Serial communication reduce wiring.
Distributed servo control system can be built by CC-Link communication.
The parameters of unit MR-PRU03 (optional) the parameter setting, operation and monitoring more convenient.
The servo amplifier can be used for speed control operation.
When the two stations are occupied, the speed can be set directly by the remote register.
Drive: MR-H_ACN series built-in positioning function.
Rated output: 0.2KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement MITSUBISHI MR-J3-15KT4 MR-J3-15KT4
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting the minimum detectable speed MITSUBISHI MR-J3-15KT4.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is larger.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method. Fiber length: 0.5 meters.
SSCNET III cables (standard optical fiber used in control cabinet) MITSUBISHI MR-J3-15KT4.
Joints for CN1A and CN1B. Type: MR-J series.
Rated output: 1.0KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: three phase AC220V.
It is very helpful to improve the stability of the low speed control of the servo motor MR-J3-15KT4 MITSUBISHI.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control MR-J3-15KT4 MITSUBISHI.
This can be effectively used in the use of the robot control of the indexing tablee MR-J3-15KT4.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment MR-J3-15KT4 MITSUBISHI.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor MITSUBISHI MR-J3-15KT4.
Encoder serial communication system, the communication frequency can only be limited to 10M.
Rated output: 0.2KW.
In servo drive speed closed loop,
Rotor speed measurement accuracy is very important to improve the dynamic and static characteristics of the speed control loop.
In order to seek the balance between measurement precision and system cost, incremental photoelectric encoder is generally used as the speed measuring sensor,
The corresponding method is M/T velocity measurement MITSUBISHI MR-J3-15KT4 MR-J3-15KT4
Although the M/T measurement method has a certain measurement accuracy and a wide range of measurement,
But this method has its inherent defects,
Mainly includes: the measurement period must be detected at least one complete encoder pulse, limiting the minimum detectable speed MITSUBISHI MR-J3-15KT4.
2 control system for speed control of the timer switch is difficult to maintain synchronization,
Can not guarantee the accuracy of measurement in the situation where the speed change is larger.
Therefore, it is difficult to improve the speed tracking and control performance of servo drive by using the traditional speed loop design method. Fiber length: 0.5 meters.
SSCNET III cables (standard optical fiber used in control cabinet) MITSUBISHI MR-J3-15KT4.
Joints for CN1A and CN1B. Type: MR-J series.
Rated output: 1.0KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: three phase AC220V.
It is very helpful to improve the stability of the low speed control of the servo motor MR-J3-15KT4 MITSUBISHI.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control MR-J3-15KT4 MITSUBISHI.
This can be effectively used in the use of the robot control of the indexing tablee MR-J3-15KT4.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment MR-J3-15KT4 MITSUBISHI.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor MITSUBISHI MR-J3-15KT4.
Encoder serial communication system, the communication frequency can only be limited to 10M.
...More relevant models >>>>