LK Automation Limited
HF-KN13J-S100 General motors for MR-JE and MR-E MITSUBISHI HF-KN13J-S100
Brand:
MITSUBISHI
Name: General motors for MR-JE and MR-E
Model: HF-KN13J-S100
Type: HF-KN servo motor, low inertia, low power.
Rated output power: 0.1kw.
Rated speed: 3000r/min.
Electromagnetic brake: there.
Oil seal: have.
Encoder resolution: 131072p/r.
S100 representative: Super MR-E special motor.
KH003 special mark for Super MR-E.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performance, high precision positioning (servo motor encoder resolution: 131072).
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface.
The analog input interface is used for speed control and torque control.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc..
Can improve the performance of equipment.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
...More relevant models >>>>
Name: General motors for MR-JE and MR-E
Model: HF-KN13J-S100
Type: HF-KN servo motor, low inertia, low power.
Rated output power: 0.1kw.
Rated speed: 3000r/min.
Electromagnetic brake: there.
Oil seal: have.
Encoder resolution: 131072p/r.
S100 representative: Super MR-E special motor.
KH003 special mark for Super MR-E.
High performance and easy to operate, reduce work load.
Enhanced system cost performance.
High performance, high precision positioning (servo motor encoder resolution: 131072).
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface.
The analog input interface is used for speed control and torque control.
Wide use.
Machining equipment and machine tool feed.
Used for food, packaging equipment and feeding device.
For textile machinery, etc..
Can improve the performance of equipment.
Servo amplifier terminals are used to reduce the required wiring time.
The connector is located in front of the servo amplifier, which is convenient for cable connection.
The gain adjustment can be easily carried out by the real-time automatic tuning function.
The length of the line: 20M.
Relay type.
IP level: IP20.
Bending life: high bending life.
Encoder with cable (amplifier side); for HF-KP/HF-MP series. Servo motor series: flat type, medium capacity.
Rated output: 0.75kw.
Rated speed; 2000r/min.
Electromagnetic brake: No.
Power supply: 200V.
The most suitable medium capacity, flat type products to limit the installation space of the situation MITSUBISHI HF-KN13J-S100 HF-KN13J-S100
Improve the environmental performance of HG-KR, HG-MR, HG-RR, HG-UR series of products using IP65.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products MITSUBISHI HF-KN13J-S100.
Can meet the different needs of different customers. Drive: MR-H_ACN series CC-LINK features.
Rated output: 11KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data MITSUBISHI HF-KN13J-S100. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive HF-KN13J-S100 MITSUBISHI HF-KN13J-S100 MITSUBISHI.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive HF-KN13J-S100 MITSUBISHI. Motor: HA-LH type.
Power: 2.0kw.
Speed: 2000r/min.
According to the types of power supply: can be divided into DC motor and AC motor.
The structure and working principle of DC motoor can be divided into four parts: brushless DC motor and brushless DC motor HF-KN13J-S100.
Brushless DC motor can be divided into: permanent magnet DC motor and DC motor.
DC Motor Division: Series DC motor, DC motor, DC motor and DC motoor MITSUBISHI HF-KN13J-S100.
Permanent magnet DC Motor Division: rare earth permanent magnet DC motor, ferrite permanent magnet DC motor and aluminum nickel Gu Yongci DC motor.
Relay type.
IP level: IP20.
Bending life: high bending life.
Encoder with cable (amplifier side); for HF-KP/HF-MP series. Servo motor series: flat type, medium capacity.
Rated output: 0.75kw.
Rated speed; 2000r/min.
Electromagnetic brake: No.
Power supply: 200V.
The most suitable medium capacity, flat type products to limit the installation space of the situation MITSUBISHI HF-KN13J-S100 HF-KN13J-S100
Improve the environmental performance of HG-KR, HG-MR, HG-RR, HG-UR series of products using IP65.
100 scene, there are 100 different drive control.
In order to meet the needs of the diverse and detailed field,
MR-J4 product line configuration, providing a wealth of servo amplifier and servo motor products MITSUBISHI HF-KN13J-S100.
Can meet the different needs of different customers. Drive: MR-H_ACN series CC-LINK features.
Rated output: 11KW.
The test system is composed of two parts, namely, the servo driver, the motor system and the host computer.
The host computer sends the speed command signal to the servo driver,
Servo drives start to run in accordance with the instructions.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data MITSUBISHI HF-KN13J-S100. Because the motor is not loaded in this test system,
So compared with the previous two kinds of testing systems, the system has a relatively small volume,
And the measurement and control circuit of the system is relatively simple,
But it also makes the system can not simulate the actual operation of the servo drive HF-KN13J-S100 MITSUBISHI HF-KN13J-S100 MITSUBISHI.
Usually, such testing system is only used to test the rotational speed and angular displacement of the tested system under no-load condition,
And can not carry on the comprehensive and accurate test to the servo drive HF-KN13J-S100 MITSUBISHI. Motor: HA-LH type.
Power: 2.0kw.
Speed: 2000r/min.
According to the types of power supply: can be divided into DC motor and AC motor.
The structure and working principle of DC motoor can be divided into four parts: brushless DC motor and brushless DC motor HF-KN13J-S100.
Brushless DC motor can be divided into: permanent magnet DC motor and DC motor.
DC Motor Division: Series DC motor, DC motor, DC motor and DC motoor MITSUBISHI HF-KN13J-S100.
Permanent magnet DC Motor Division: rare earth permanent magnet DC motor, ferrite permanent magnet DC motor and aluminum nickel Gu Yongci DC motor.
...More relevant models >>>>