LK Automation Limited LK Automation Limited
Download Sort: OMRON | MITSUBISHI | Proface | Mennekes | Yaskawa
Home >> Catalog Download
MITSUBISHI MR-J2-20A datasheet PDF
Product model: MR-J2-20A
Name: Universal interface driver
Brand: MITSUBISHI
Sort: PDF datasheet
File language: English
Type: MR-J series.
Rated output: 0.1KW.
Applicable motor series: HA-FF, HA-SE.
Voltage: single phase AC100V.
It is very helpful to improve the stability of the low speed control of the servo motor.
But there is no direct effect to improve the accuracy of position control.
There are, of course, software compensation that is similar to pitch compensation,
Can improve the physical resolution of the single lap, so as to improve the accuracy of positioning control MR-J2-20A PDF MR-J2-20A
This can be effectively used in the use of the robot control of the indexing table.
It is also because of the application of splicing technology,
The rotary encoder will be more widely used in the high precision servo control in the harsh environment MR-J2-20A PDF.
The use of rotary encoder with 224/ in the servo motor has been used in the servo motor.
Encoder serial communication system, the communication frequency can only be limited to 10M. Type: general purpose AC servo amplifier MR-E series.
Rated output: 0.4kw.
Interface type: general purpose pulse interface.
KH003 special mark for Super MR-E.
High performance and easy to operate, reduce work load MR-J2-20A PDF.
Enhanced system cost performance.
High performance, high precision positioning (servo motor encoder resolution: 131072).
High response.
Suppression of vibration by adaptive vibration suppression control.
Using personal computer and servo setup software to optimize tuning.
Has 2 types of interfaces:
Position control and speed control with pulse train interface.
The analog input interface is used for speed control and torque control. The length of the line: 2M.
IP level: IP65.
Bending life: standard.
The cable is not shielded.
Electric motor power supply cable for HF-KP/HF-MP series (motor shaft with side extraction). 1 axis servo amplifier.
MITSUBISHI general AC servo amplifier MELSERVO-J4 series.
Rated output: 15.0kw.
Interface: SSCNET III /H.
Power supply: three phase AC200V.
Special specification: full closed loop control 4 wire / device end encoder ABZ phase input corresponding support function security unit, support positioning mode.
Servo amplifier supporting SSCNET III /H.
Complete synchronization system capable of using high speed serial optical communication.
Can be combined with the servo system controller to maximize the performance of the servo system.
The industry''s top level speed motor, the frequency of 2.5kHz amplifier, and optical fiber network extradimensional Symphony orchestra.
Using the traditional two degree of freedom model adaptive control to further opptimize the exclusive high speed servo control structure of the dedicated execution engine MR-J2-20A datasheet.
Achieved the fastest 2.5kHz speed frequency response in the industry.
Combined with MITSUBISHI independent research and development of hiigh resolution absolute position encoder (4194304pulses/rev),
Greatly improve the processing speed MR-J2-20A datasheet. Can maximize the performance of high-end machinery.
Related products
MITSUBISHI
Servo driver
MR-J4-11KA
MITSUBISHI Servo driver MR-J4-11KA
1 axis servo amplifier. MITSUBISHI gener
MITSUBISHI
SSCNET III fiber
MR-J3BUS20M-A
MITSUBISHI SSCNET III fiber MR-J3BUS20M-A
Fier length: 20 meters. SSCNET III cal
MITSUBISHI
Universal pulse interface driver
MR-J3-22KA4
MITSUBISHI Universal pulse interface driver MR-J3-22KA4
MITSUBISHI motor universal AC servo ampl